I haven't used stormycloud much but i haven't heard there being issues with them. I've preferred using outproxy.acetone.i2p and purokishi.i2p since i've found them consistently to be faster. Stormycloud is the default in vanilla i2p so they end up getting the brunt of i2p's outproxy traffic, it's possible they could get overloaded. They have a very good setup, but they're one entity.

Especially right now after mental outlaws video, more routers could be coming online and giving stormycloud a workout, maybe getting overwhelmed. I would try switching to either of those and setting inbound/outbound tunnel count to 16. hope that helps.

Here's the scary sounding part that can be counterintuitive. The routers you're communicating with do know your ip, since they have to like you mentioned. Your ip address is also in i2p's DHT as a "router info" which functions as a network addressbook for routers and services so things can be found without needing a centralized lookup service. Again, because for the network to work, routers need to be able to find eachother, or they can't communicate.

But, routers function on a need to know basis. i2p uses separate up and down links for each tunnel, and your side of the tunnel by default has 3 hops. other side usually also has 3 hops. typical unidirectional tunnel looks like this with total of 7 hops:

A-x-x-x=x-x-x-B

None of the chains in the link know what position they're in (except for the endpoints). They also don't know how long the whole tunnel is. The sender and receiver only know their parts of the tunnel. On the dht side, by design no single router has a whole view of the network, but there isn't a whole lot of information you get from that other than knowing that person at stated ip address uses i2p, which your isp would be able to tell for example anyway just like using tor or a vpn. There's no reason to try to obfuscate that except for getting around restrictive countries firewalls.

The way i made sense of it was like you have an envelope that is inside several other envelopes, with each envelope representing a layer of encryption. You get an envelope from kevin, so you know kevin. You open the envelope and see another envelope addressed to george, you give the envelope to him. So you know kevin and george. But the rest is unknown to you. You don't know who the true originator of the envelope is or where the message is ultimately going.

Not a perfect analogy, but because of this the ultimate sender and receiver are blind to each others ip address. It's layered encryption allowing this to happen which is similar to onion routing. Called garlic routing in i2p since there are some tweaks.

https://geti2p.net/en/docs/how/garlic-routing

yeah some of the docs on the official site lean more technical than practical

similar yes but not the same. tor held together by volunteer that run nodes, i2p everyone is a node. tor good for clearnet things, i2p good for in-network things. torrenting in i2p is good for i2p, not tor. torrenting in i2p stays in the i2p network, doesn't go through exit nodes. there's only about 3 of those. it's torrenting as a darknet hidden service.

Yeah, accessing the outernet was sort of an afterthought with i2p, although the proxies are handling well now...things got way better after stormy cloud came on the scene imo. you can stream clearnet videos through the 3 i mentioned. It could be better if there was outproxy switching built in like tor, i think. It was bad though before stormy cloud and often unusable, the available outproxies were very much overwhelmed. sometimes they worked but it was hit or miss.

that's the right line of thinking. vast majority of tor users don't contribute to the network which is held together by a comparatively small number of volunteers. by default if you're running i2p you're contributing (except with specific configurations). With tor, more users, same number of nodes means less bandwidth for everyone. With i2p more users means both sides go up, more nodes, more bandwidth, on average more bandwidth for everyone. Torrenting burns bandwidth but on average more users grows network capacity.

here's an i2p magnet link to the irs chain analysis talk from last year:

magnet:?xt=urn:btih:d371d4e4cb9a3760ef79e94fde0b8edf22062e49&tr=http://tracker2.postman.i2p/announce.php&dn=chainalysis-monero-presentation-to-irs-august-2023.av1.webm

gives some insight into how they do it with their analysis tool. i'll let you draw your own conclusions based on your own risk profile, but if you're a target and they have enough confidence with the tool, they could grow a profile and subpoena the target exchange for kyc.

do not the vpn

It's 2024 back that shit up on a dictaphone already

welcome!

welcome!

100% right, tor is not for torrenting, tor for clearnet

i2p for torrenting, not for clearnet

You can do multihoming, might be the easiest thing to do for a service: https://geti2p.net/spec/proposals/140-invisible-multihoming

Multihoming is a pretty simple way of load balancing and i think the way it works is the first router to respond is the one that's used. So ideally the one used by any given client should be the most responsive i2p router.

It's also used to place i2p routers hosting a service in multiple places so it makes correlation attacks (ex downtime at exact time of a known electric outage in an area) more difficult.

Backend setup for your service

If we have a service like an http proxy service or a website available on port 6000, and 2 i2p routers, they'd both need access to that port. An outproxy may do this with port forwarding from a clean outernet connection(s) going through their proxy setup ex privoxy/haproxy/tinyproxy dns. They're less worried about correlation attacks so the routers may be all or mostly in one area using port forwarding over lan or VM's. A website that's concerned about correlation attacks may have separate instances of the website running on each router in different areas, with the website's backend syncing with the other routers in the background through other methods such as an encrypted lease-set.

Router setup

Each router needs the same exact key for the actual .i2p address. The easy way to do this is in the java router (i2p+ is good for this, install guide/official site go to service tunnels > make new server http tunnel, enter the port 6000, give it a name like "Outproxy", private key file a name like "outproxy.dat" and make sure optimize for Multihoming is on.

Other recommended additions in your tunnel config

• Automatically start tunnel: on
• 16 tunnels in/out (maximum): 3 hops for good anonymity, outproxies not concerned with their own anonymity could reduce this for more performance.
• Reduce tunnels to conserve resources: idle period 15-20 minutes, reduced count: low number like 2-3. This usually works well since the tunnels can be built back in an order of ms's on a good i2p router and not wasting resources keeping them open. It could introduce a slight delay though. High traffic situations might make sense to leave that off.

Then save and start, key file is generated.

Copy key file and a tunnel config file

Locations for .config file and key (.dat):

/i2p/.i2p/outproxy.dat

/i2p/.i2p/i2ptunnel.config.d/XX-outproxy-i2ptunnel.config

Then copy the key and config files to the other i2p routers in the same locations. Shouldn't need to go through setup with the config file present. Most important is it has the same key file, so they'll all use the same address.