Any ideas as to what I'm doing wrong?
This sphere has a ridge on it, and I've had miniatures come out with the base to be slightly offset giving a bit of a ridge.
I'm using a Halot One, lychee Slicer, and Anycubic Water Wash resin.
this post was submitted on 25 Nov 2023
72 points (96.2% liked)
3DPrinting
15577 readers
297 users here now
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
Rules
-
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
-
Be respectful, especially when disagreeing. Everyone should feel welcome here.
-
No porn (NSFW prints are acceptable but must be marked NSFW)
-
No Ads / Spamming / Guerrilla Marketing
-
Do not create links to reddit
-
If you see an issue please flag it
-
No guns
-
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
founded 1 year ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
Given my experience, this is what I would say too. Not separating from the FEP. Very specifically, I notice he's printing a sphere. These are known to cause suction-cupping, and generally the symptom of said suction cupping is...this.
Suction cupping causes the print to rip from the build plate/supports, it wouldn’t cause this. Especially since it continues along as if a few layers were cut out of the file, which just isn’t something caused by suction cupping. It would essentially need to be stuck to the FEP to such an extreme degree that the stepper motor is unable to move.
It can cause both, actually. And it continues along, because it eventually gets up high enough in layers that the additional lift manages to break the suction effect. Finally allowing the resin to drop out of the top of the model and for it to cease happening. If the FEP film isn't tight enough, or has loosened up due to wear, it absolutely can follow the print upwards without disconnecting for a few layers, without pulling the print off of the build plate.
I, quite literally, run one of the few professional shop for repairing FDM and Resin based printers in the USA and have 12 years of experience in the field; engineering systems, designing products, and even had a few successful 3D printer kickstarters. Sure - without looking at it happen in person, I could be missing something here, but I highly doubt it.
Additionally, I've seen this exact failure mode on the peopoly Phenom due to its excessively large FEP vat, as mentioned - due to suction cupping. The model never separated from the build plate. The motor doesn't have to cease moving, you merely need too little lift, and a loose FEP film.
A loose FEP wouldn’t cause the print to essentially perfectly skip over multiple layers. Once the FEP finally releases, there would be multiple layers missing, resulting in a very gloppy thick layer, or the remaining layers printing directly on the FEP.
I can’t think of any situation a loose FEP could result in the above image without at the very least one “extremely large” layer.
Not to mention, the FEP wouldn’t suddenly tighten, meaning you’d have the same issue over and over.
Suction cupping could be a possibility on the sphere, it does not explain why I had ridges on miniature prints.
A loose FEP film can explain the ridges, which would exacerbate the ability for a part to suction cup like that. I mentioned that, as they're interrelated.