28
Home assistant cheap pool sensor? (sh.itjust.works)
submitted 1 year ago by Fenixin@sh.itjust.works to c/homeassistant@lemmy.world
12 comments fedilink hide all child comments

Hello!

I moving to a new home with a small pool and I was thinking of buying a pool sensor.

Right now I'm searching for something simple like temperature but would be nice to have ph and others.

I'd like it to be local, no cloud, and right now something cheap, I love DIY stuff.

So, any recommendations? Any experiences with these kind of sensors? My searches lead to pretty expensive stuff that can measure all the pool parameters and cloud based.

Thanks for reading!

top 12 comments
sorted by: hot top controversial new old
[-] Yazer@lemmy.ca 5 points 1 year ago

I went with inkbird for something similar. They are Bluetooth, with a cheap wifi module as well. Wide range of sensors. Cost me 60 in total to monitor my hottub temp when I'm in Mexico and it's -40 at home

[-] Fenixin@sh.itjust.works 1 points 1 year ago

Thank you! Just checked it and it looks really nice. How do you integrate it with home assistant? I've been checking the inkbird integration and it seems to be Bluetooth only. I'm afraid Bluetooth is not an alternative, the HA server is in the basement and is not going to reach the pool by Bluetooth

[-] ciscoqid@lemm.ee 3 points 1 year ago

I set this up recently with an ESPHome Bluetooth proxy on an m5stack atom. As long as the proxy can be on WiFi and see the Inkbird, works great.

[-] Psiczar@aussie.zone 5 points 1 year ago

I built a pool water temp sensor using an ESP32 and a DS18B20. I drilled a hole in the pump intake pipe, installed it and now I always know the temp of the pool.

I cant find the original page I used to build it but it wasnt hard and there are similar guides online. Here is the code I am using on the ESP32

esphome: name: esp-pool-temp

esp8266: board: esp01_1m

Enable logging

logger:

Enable Home Assistant API

api:

ota: password: "fa053faa36e5d6600a5613086aaca3ca"

wifi: ssid: password: fast_connect: true

Enable fallback hotspot (captive portal) in case wifi connection fails

ap:

ssid: "Pool-Espboard Fallback Hotspot"

password: "MCueN8HiEEvS"

captive_portal:

Example configuration entry

dallas:

  • pin: GPIO4

Individual sensors

sensor:

  • platform: dallas address: 0xE93C01D607349D28 name: "Pool Temperature"
  • platform: wifi_signal name: "WiFi Signal" update_interval: 60s
[-] Fenixin@sh.itjust.works 1 points 1 year ago

Nice idea! Will study the possibility in my pool. Thanks!

[-] Ambrotos@lemmy.ca 4 points 1 year ago

I know you said "cheap", and this isn't exactly that... but I thought I'd mention it as an option anyway. I went with the Atlas Scientific pool kit when automating my pool. It gives me pH, Temp, and ORP. They also have a dosing pump if you want to automate chemicals. It's based on an Adafruit ESP8266, so you can flash esphome on it, making integration with Home Assistant dead simple. https://atlas-scientific.com/kits/wi-fi-pool-kit/

You can go the DIY route for temperature with a $5 ESP8266 off Amazon and a $1 thermistor, but I don't think there are similarly cheap options for pH and ORP.

[-] Fenixin@sh.itjust.works 1 points 1 year ago

That looks amazing. But it's out of my budget right now. Thanks for the suggestion!

I've been thinking about the DIY route for some time but creating a water and weather proof enclosure it's not easy.

[-] Ambrotos@lemmy.ca 1 points 1 year ago

I don't think you need to stress too much about weatherproofing your DIY enclosure. You can get "weatherproof" boxes off Amazon for ~$20, and as long as you mount it somewhere out of direct exposure (e.g. near your pool controller under an eave) you'll be fine. For example, I built an irrigation control valve for an unrelated project into one of these boxes and mounted it to the back of my garden shed. It even comes with 2 cable glands. https://a.co/d/j7hkyDX

Then you can just run a cable over to a section of your pool's PVC piping (probably just after your pump), drill a small 1/4" hole and stick a thermistor into the flow. Something like this is designed for exactly this purpose: https://a.co/d/994WUHf It's even got an o-ring to seal the hole, you just hold it onto the pipe with a cable tie. Whether you get a Pentair-branded temp sensor or not, they're mostly all 10kOhm thermistors, which you can easily add to ESPHome as an NTC sensor: https://esphome.io/components/sensor/ntc.html

Hope that helps. I'm also a big fan of DIY :)

[-] Rhs519@lemmy.ca 1 points 1 year ago

If your willing to home brew a solution, check out the esphome project. It’s very easy to implement and runs on very inexpensive esp32 boards.

I’ve got something similar, but less ambitious running at my place (temp only). It’s been solid for about 6 months now.

[-] Fenixin@sh.itjust.works 2 points 1 year ago

Thanks! I have a few answers with same suggestion, will check all this out!

[-] Yazer@lemmy.ca 0 points 1 year ago

I don't integrate with home assistant. Not really sure the benefit. I guess asking Alexa to check the temp?

Have you looked into the wifi module? Then it's not wifi only

[-] Fenixin@sh.itjust.works 1 points 1 year ago

I love the graphs and the seeing how every variable make changes in what I'm measuring.

But that is just me

this post was submitted on 02 Jul 2023
28 points (96.7% liked)

homeassistant

11833 readers
10 users here now

Home Assistant is open source home automation that puts local control and privacy first. Powered by a worldwide community of tinkerers and DIY enthusiasts. Perfect to run on a Raspberry Pi or a local server. Available for free at home-assistant.io

founded 1 year ago
MODERATORS
GreatAlbatross@feddit.uk