3DPrinting

15618 readers

408 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts

If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago

MODERATORS

andypiper@lemmy.world

henry_rowengartner@lemmy.world

j4k3@lemmy.world

GrayBackgroundMusic@lemm.ee

Thermometers reading different temperatures on cold printer? (lemmy.world)

submitted 6 hours ago by IMALlama@lemmy.world to c/3dprinting@lemmy.world

5 comments fedilink hide all child comments

I am in the process of buttoning up a Nitehawk conversion on my Voron. I also replaced my extruder thermistor with an OE replacement purchased from a reputable vendor.

Post setup, my heated bed is reading spot on (it's 18.3 C in my basement aka 65 F). I verified that my extruder is also at ambient temperature by wedging a Thermapen under its silicone sock and letting it acclimate for 10 minutes. The I'm not sure why the extruder would be reading high.

I bought a spare thermistor and wired it in. The result was identical.

Thoughts? Ideas? I'm pretty sure I have the Nitehawk and thermistor set up correctly.

[extruder] step_pin: nhk:gpio23 dir_pin: nhk:gpio24
enable_pin: !nhk:gpio25
heater_pin: nhk:gpio9
sensor_pin: nhk:gpio29
pullup_resistor: 2200
sensor_type: ATC Semitec 104NT-4-R025H42G`

top 5 comments

sorted by: hot top controversial new old

[–] Ediacarium@feddit.org 3 points 2 hours ago* (last edited 2 hours ago)

My Voron with its nighthawk is currently printing, so it's gonna take some time until I can see how much deviation I get.

You have a spare ` at the end of your sensor_type, maybe Klipper falls back on a generic resistor?

Otherwise could the thermistor conduct some heat from the nh processor? (Maybe through the cable?)

[–] morbidcactus@lemmy.ca 2 points 3 hours ago* (last edited 3 hours ago)

My voron with can toolhead, using a pt1000, I'd accept +/- a degree or so but that's a bit more than that. Could trying calibrating the pullup value manually? I'm using Generic 3950 for the sensor types on the Semitec 100k thermistors (chamber temp and plate temp are both using one of those), had the best results with that personally, could see if that helps things.

[–] aubeynarf@lemmynsfw.com 7 points 5 hours ago (1 children)

are these packaged thermometer devices, such as the DS18B20, or a bare thermistor bead?

If it’s just a bead, you probably need to calibrate them.

[–] IMALlama@lemmy.world 5 points 5 hours ago (1 children)

They're 104nt's. I have never calibrated a thermistor for one of my printers before, other than updating the firmware (compile marlin, config Klipper) and choosing the appropriate value.

I did dig up a datasheet for the thermistor, will have to check resistance tonight.

[–] SzethFriendOfNimi@lemmy.world 1 points 3 hours ago* (last edited 3 hours ago)

If they’re on board that could be their idle ambient temps.

The currents running through them, resistors, etc all generate some heat.

I tend to look at board temps less about the environment and more about how the board is doing.

Is it suddenly running very hot, etc.

As for the extruder it is attached to a thermal mass. So it may take longer to adjust but you did say it’s been sitting there for a bit.