Correct and sounds like the best of both worlds
I'll grab a kitchen sponge
You can just cut 30x30 mm peace and zip-tie it over filament ๐
Enclosure will protect printer from dust and it will also keep the ambient temperature more stable. Dont make it hermetic sealed, better add few holes on the front and few on the back for example. I have a low rpm fan with dust filter because I mostly print PLA and in long prints (12h+) temperature can go a bit too high if there is no airflow at all. Keep in mind that enclosure should be removed sometimes for mintainance, removable sides is what you should look for.
You can leave filament on the printer, but if you dont use it for a long time it could get wet and then you have to dry it. Keep the rest of the spools in plastic sealed box or bag and put some silica gel inside.
Full calibration should be done once, but fine tuning when you face some issues or when you change to different brand or filament type. It depends how well the printer is assembled and how experienced you are, it can take only 5 min every few months, but begginers can spend days sometimes.
Extra tips: clean your rails and wheels whenever you can (once a month at least) for dusty garage. Get a kitchen sponge, drill a hole in it and guide filament trough the hole to remove any dust before extruder.
Welcome to the most fun hoby and happy printing!
He is horny ๐
Daily backup to backblaze b2 and also to local storage with kopia. Its been running for a year I think, no issues at all. I didnt need a real backup yet, just did some restore tests so far
If OP cant use more than one disk at once, how can they benefit from mergerfs?
In my country pi4 8GB ram with PSU 130โฌ and then you need SD card and/or SSD
Adding my data as well:
My server is diy desktop pc - mbo MSI Z270-A PRO with celeron G3930 and 16GB RAM, 3x SSD on 550W PSU, idles at 23W. After adding another 3.5" HDD consuption went up to 34W. 34W in Ctoatia is around 34โฌ a year.
Some SFF PCs are at 10-15W. SBCs like rpi should be below 10 W, but dont think you can get anything new for 80โฌ
Your cpu supports quick sync so I bet you are good without gpu. Try it yourself before buying one, you also drain less power
-4c is extreemly cold, get thermometer inside of enclosure and leave your heatbed on until it reaches 10-15C before you start printing. Even better get enclosure heater. Id also bump nozzle temp to the highest marked on your spool.
Why lower if you print everything at the same layer height?
Hey guys, I have Corsair RM550x that is turning on/off its fan in 65-70 min cycles when PC is on idle. When PSU fan is off I meassure 31W from wall and 21W when fan is off. Other PSUs are not like that and they are around 25W. Funny thing is that fan shouldnt even spin below 220W iirc and I found it hillarius that its using less power when fan is on. PC is working fine, but is this normal?
Edit: specs - MSI Z270-A PRO, intel G3930, 8gb ram, 2 sata SSD and no GPU
Edit 2:
Thank you all for helping me out!
I believe that no flow in case caused PSU overheating and due to lower efficiency at higher temp PSU was using more power. Enabling case fans with small positive pressure fixed the problem immediately and now its stable at 24W on idle. On the next diagram PC was idle for only short period of time, so you can also see power curve when it was running some services, but still "much" less than 30 W.
Edit 3: Before this post I asked Corsair about that, but got only bot level responses. Conversation was going in circle and then I gave up :D
Hey guys! Its lovely to see this community is active on lemmy, keep it up!
Just wanted to share my recent project. Low powered PC is ticking inside of this PLA case and its silent home server
Hello lemings and old redditors!
I have counter for each of medication that gets decrement with automations once or twice a day at specific time. That works fine, but now I'd like to see for how many days I have pills left before I have to resupply. For example I take 2 pills of decortin per day and since there are 8 in counter I have enough for next 4 days and that will be on 21.06.2023. But I take 4 pills of envarsus per day and that means I have to resupply in 7 days since there are only 29 pills left. So basically I want a Card on my dashboard with 2 additional columns, how can I do that?
One of the first services on my server was nextcloud in docker container from lsio. Never had problems so there was no need to try AIO, but so many people recommend that, it will be my next setup if this one fails me