Oh you want this stuff by a brand called Hagesan Blue, sometimes listed as "HG". It'll be obvious which of their products to get though if I recall a few are suitablr.
Ryman's used to sell it.
this post was submitted on 31 Oct 2023
7 points (100.0% liked)
Do It Yourself
7718 readers
1 users here now
Make it, Fix it, Renovate it, Rehabilitate it - as long as you’ve done some part of it yourself, share!
Especially for gardening related or specific do-it-yourself projects, see also the Nature and Gardening community. For more creative-minded projects, see also the Creative community.
This community's icon was made by Aaron Schneider, under the CC-BY-NC-SA 4.0 license.
founded 2 years ago
MODERATORS
I have this very same issue, and I found that Scrubbing Bubbles worked well. You just need something below to catch the filth that will run off. The bubbles penetrate the porous surface and draw out the soot.
If you can't get scrubbing bubbles, then baking soda and vinegar would create the same kind of bubbling action but you'll need the right proportions so as not to leave a baking soda residue.
Seconding oxyclean or a similar surfactant for the cleanup.
Second piece of (possibly unwarranted) advice: Do your best to load the box in such a way as to minimize fiddling during active burn times. We have a small fire box so for us it's usually a sort of Z pattern with two parallel logs and a cross piece. Play around with a few configurations to figure out the best layout for yours - the manufacturer may have suggestions. The goal is to set them up in such a way that the bottom logs collapse and let the top ones come down into the renewed coals, then turn to coals themselves. That's the optimal time to insert fresh logs to minimize ash and smoke escaping into your residence.
Thaks for the oxyclear tip and yeah, loading the fire up initially is something I struggle with - it stays in our it goes out. I'll try that loading fashion - cheers.
We used to have the problem of smoke, etc, escaping in to the room. We changed how and when we opened the door, and how we loaded it up.
Now we use the top down method to start a fire, it produces less smoke.
We use just kindling to start, which is best for my burner.
And we leave the air controls open for all of the first burn of the day.
When the first load is down to embers -btw, embers don't smoke- we leave the air controls open.
Get the next logs ready.
Open the door slowly.
Then load up again quickly, but without just chucking the logs in.
We leave the air controls open until the new load is burning nice then shut them as needed.
On the next load we do the same routine.
Now we only ever get smoke escaping in to the room if we have to open the door during the first part of a fresh load of logs, such as if the logs fall incorrectly and touch the glass.
Great advice and thanks for taking the time.
For what it's now worth, this has been my way so far (which by the sound of it may be why I'm unsuccessful): load kindling, one log and a couple of firelighters, light fire, keep control open and also door.
Close door after 3-4 mins, wait until log is burnt on one side then turn it over, wait until its burnt through then add another log then repeat turn and refill.
Not getting chance to watch tv properly as I'm constantly watching the fire!
Do you find any type of log better than others?
Thanks again for the advice.
Ok, buckle up, it's time for an essay.
Firstly, it sounds like your burner, like mine, doesn't like too much timber inside of it on the first burn of the day.
Remember that everything is 'cold'. Your flue, the fire bricks, the burner. And all that needs to get warmed asap and will 'steal' that heat from the fire. Which will make the flames choke, especially when compared with a hot burner.
Plus if you have to turn the log to keep it burning then you don't have enough heat (embers, or flames) under it to keep it on fire.
And that's even if it's not the first fire of the day.
The only time I need to mess with a log is if they have fallen against the glass.
I try to keep about an inch of ash in the firebox for insulation. And try to keep an inch of embers running so the logs get hot enough to burn.
We tried numerous ways of starting fires.
Bottom up.
Logs in an arrow shape facing to the back of the burner with kindling at the front.
Logs like a teepee, with kindling under it.
Logs as a proper V shape with kindling under and over.
But every time it would struggle and/or smoke a lot.
Now, like I said, we just use kindling with the top down method. We put in 4 inch sized firelighters under the top piece of kindling and fire it up. 99 percent of the time it'll start no problems, and far less smoke.
If we put anything other than kindling in it will be very small logs, almost branches sized, nothing more.
Once the fire is going with a decent amount of embers then we can chuck the logs in but leave the air controls open and, again, 99 percent of the time it'll catch. Then we will just shut the controls a bit later as needed.
You need 3 things to start and keep a fire going: ignition(fire). Fuel. Oxygen(air).
Too much, or too little, will cause it to go boom. Go out. Or smoke.
Having the correct amounts of each will, usually, mean you have a good fire.
You want to eliminate as much smoke as possible. It'll cause creosote, etc, and if that catches ignites you'll have a chimney fire. Which, obviously, is bad.
Then there's the logs. If they aren't 'dry' you'll also struggle to keep things burning because you are adding another element (sap, water) to it all.
The 'wetter' the wood the more air you'll need to keep the same sized log on fire.
If you haven't got a moisture tester for timber then you defo should get one. Anything under 20% is great.
Logs. We burn anything. Hard, soft. It doesn't matter. As long as it is dry it burns.
If we have hardwood we'll leave that until the fire is going. We'll start with kindling, then a few softwood then hardwood.
If the fire is hot enough it won't smoke.
I've got to go to work. Any questions then just ask
Hi, apologies for the delay in replying and thanks for the advice - I've been following it this weekend after getting some more logs.
So far it's working well - I'm on top-down (Scandinavian) method - gets a really nice fire going quick and heats up the flue pretty quickly too. Your tip on getting a moisture tester: I'm gonna follow up soon when I get paid. I get that it's going to be pretty useful.
I got the two controls mixed up: left being main air vent (which I now keep open until the fire gets red hot) and the right (which I used to keep closed all the time) and now leave open. So, it's running pretty nice now, my next challenge is keeping it going! I got some complaints that the room was going cold so I'm not sure if leaving the logs to go to embers was leaving it too late before putting more logs on.
Again, thanks for the heads up, this is a learning curve for us, but I really appreciate the help.